Skip to Content
Events Contact Us
Close
Technical Guides

Runway Guard Lights and Stop Bars: Applications and Selection

Functions, layouts and control requirements for selecting runway guard lights, stop bars and intermediate holding position lights.

Runway Guard Lights and Stop Bars: Applications and Selection

Runway guard lights warn traffic approaching a runway. Stop bars provide a controlled red stop signal, while intermediate holding position lights identify holding positions along taxiways. Selecting these lights requires an understanding of the position's purpose, minimum operating runway visual range (RVR), traffic density and the airport's power and control arrangements.

Combining runway guard lights and stop bars

Runway guard lights use alternating yellow lights to make a runway-holding position more conspicuous. A stop bar adds a red signal controlled by air traffic services. The two functions can be used together at one holding position.

Configuration A has one elevated pair on each side of the taxiway. Configuration B forms an inset row across its width, with lights 3 m apart. Both arrangements face approaching traffic and sit on the holding side of the marking. Lights alternate within each elevated pair; in the inset row, adjacent lights alternate and alternate lights flash together. ICAO specifies 30–60 cycles per minute.

ICAO recommends against collocating Configuration B with a stop bar. Where both functions are needed at the same position, Configuration A provides an elevated option alongside the red bar.

Annex 14 requires Configuration A at taxiway/runway intersections associated with a runway intended for either of these conditions:

  • RVR below 550 m, where no stop bar is installed.

  • RVR between 550 m and 1,200 m, with heavy traffic.

The second condition also applies where a stop bar is present. At identified runway-incursion hotspots, ICAO also recommends guard lights for daytime and night-time use in all weather.

Stop bar applications

ICAO requires stop bars at runway-holding positions serving runways intended for RVR below 550 m. Its exceptions depend on appropriate aids and procedures preventing inadvertent incursions, or low-visibility procedures limiting the manoeuvring area to one aircraft at a time and the essential minimum of vehicles. Stop bars can also form part of runway-incursion prevention measures at night and in better visibility.

The inset red row extends across the taxiway, uniformly spaced no more than 3 m apart. Where snow, rain or aircraft structure could obscure it, ICAO recommends supplementary elevated pairs at the ends. At intermediate holding positions, it recommends a stop bar where lights are needed to supplement markings for visual traffic control.

In normal controlled operations, runway entry or crossing requires the appropriate ATC clearance as well as an extinguished stop bar. A lit red bar requires a stop, even when a clearance has been issued.

Intermediate holding position light applications

Three steady, unidirectional yellow lights identify an intermediate holding position. They face approaching aircraft, symmetrically across the taxiway centre line at 1.5 m spacing, 0.3 m before the marking on its holding side.

Under ICAO Annex 14 Volume I, Amendment 18, these lights are required at intermediate holding positions intended for RVR below 300 m, unless a stop bar is already installed there. The amendment became applicable on 27 November 2025. ICAO also recommends these lights where no stop/go signal is needed.

FAA guidance uses the term clearance bar for a three-light, steady-yellow inset arrangement on taxiways. For a project following FAA standards, confirm its application and layout against the FAA design documents specified for that project.

Power, interlocking and status monitoring

A stop bar must interlock with the taxiway centre line lights beyond it. When the bar is lit, centre line lights for at least 90 m beyond the bar towards the runway must be off. The red stop signal and that green guidance are mutually exclusive.

The electrical design should prevent a common failure from extinguishing the entire bar. ICAO requires automatic monitoring where lights are used for aircraft control, with faults affecting that function reported to air traffic services. It recommends indication of a changed runway-holding stop bar state within two seconds. Confirm switching, failure detection and feedback with the power and control system supplier.

Product selection and project information

Select the fixture after establishing the holding position's function and layout. These Airsafe LED models cover the main roles; elevated stop bar fixtures provide supplementary indication at the ends.

Model

Role

Product page

EUL-RG-LED

Elevated Configuration A runway guard light

View product

RGLZ-08-LED

Inset Configuration B runway guard light

View product

EUL-SB-LED

Supplementary elevated stop bar light

View product

SBLZ-08-LED

Inset stop bar light

View product

TPLZ-08-LED

Intermediate holding position light, installed in groups of three

View product

For FAA-based specifications, AC 150/5340-30J covers visual-aid design and installation, while AC 150/5345-46F defines fixture requirements, including L-804 elevated and L-852G inset runway guard lights. Identify the required fixture type and qualification documents when selecting the model and configuration.

For an enquiry, provide the minimum operating RVR, holding-position plan, existing stop bar layout, applicable standard and edition, and power and control requirements. Retrofit projects should also include existing fixture, base and constant current regulator (CCR) details. Contact Airsafe engineering.

Related guides cover threshold, wing bar and end lights and the RETIL 3-2-1 layout.

Frequently Asked Questions

Does a stop bar remove the need for runway guard lights?

Not automatically. ICAO requires Configuration A for runways intended for RVR between 550 m and 1,200 m with heavy traffic, including intersections already equipped with stop bars.

Can Configuration B be collocated with a stop bar?

ICAO recommends against it. Configuration A provides an elevated option where both functions are needed at one holding position.

When are intermediate holding position lights required?

ICAO Amendment 18 requires them at intermediate holding positions intended for RVR below 300 m, unless a stop bar is installed there. Confirm the standard and edition adopted for the project.

Does an extinguished stop bar permit runway entry?

Extinguishing the bar does not constitute ATC clearance. In normal controlled operations, the appropriate clearance and airport procedures still apply; a lit red bar requires a stop.

Subscribe to Airsafe updates

Product releases, upcoming events and industry updates — unsubscribe at any time.